Indice
Pubblicazioni
Cerca
Ultime immagini
Registrati
Accedi
Ciao a tutti
Come da titolo vendo l’ampli in oggetto, di cui si è parlato in abbondanza (e molto bene) su questo forum.
Si tratta della versione “top” con alimentatore lineare e telecomando.
L’ampli è in ottime condizioni, l’unico difetto visibile è l’adesivo bianco intorno all’uscita cuffia che si è parzialmente staccato come visibile in foto.
Prezzo : 1200 euro
Di seguito le specifiche come da sito del costruttore:
SPECIFICATIONS
Amplifier class: Push-pull Class A, no feedback
Sensitivity: 0.6V RMS [full output]
Output impedance: (measured @ 0.5A, 60 Hz) 2 ohms
Input impedance: 50k
Power Supply Input: Auto-switching 100V / 120V / 220 / 240V operation or linear supply user-switchable between 110/120 and 220/240 (contact us if in need of a 100V linear supply)
Power Supply Output: 12VDC 2.5 amps
Hum and noise: minimum 60mV RMS or 90dB below full output (20Hz-20kHz)
Power consumption from ac power source: 33W
Power output: with 4-ohm load: 1W, 1% THD, with 14-ohm load: 0.5W, 1% THD
Channel separation: (4-ohm loads) 46dB, 100Hz-10kHz, (14-ohm loads): 54 dB, 100Hz-10kHz
Frequency response full power: (4-ohm load) +0, -1dB 10Hz-20kHz, (14-ohm load): +0, -1dB 5Hz-50kHz,
Voltage gain: (4-ohm load): 10.3dB, (14-ohm load): 12.4dB
Size:
Amplifier: 9 1/2 inches (24.1 cm) wide, 4 3/4 inches (12.0 cm) tall, 7 7/8 inches (19.7 cm) deep (including connectors)
Linear power supply: 12" (30.48 cm) x 3.25" (8.26 cm) x 4.25" (10.8 cm)
Net weight:
With switching supply: 5.35 lbs (2.5 kg) - amplifier and external power supply)
With linear supply: 8.94 lbs (4.1 kg) - amplifier and external power supply)
Finish: Aluminum case w/ lexan top
Tube complement: 2 x 12AT7 input, 2 x 6SN7 or 12SN7 output. (We supply NOS 12SN7 tubes by default. Jumpers on the circuit board allow you to easily switch between 12V and 6V, allowing you to use both 6SN7 and 12SN7 tubes and expanding your tube choices. The 12SN7 and 6SN7 are sonically identical and differ only in their heater voltage.) 12AU7 tubes can replace the 12AT7 tubes to lower the gain.
[url=https://servimg.com/view/20314502/54]
Come da titolo vendo l’ampli in oggetto, di cui si è parlato in abbondanza (e molto bene) su questo forum.
Si tratta della versione “top” con alimentatore lineare e telecomando.
L’ampli è in ottime condizioni, l’unico difetto visibile è l’adesivo bianco intorno all’uscita cuffia che si è parzialmente staccato come visibile in foto.
Prezzo : 1200 euro
Di seguito le specifiche come da sito del costruttore:
SPECIFICATIONS
Amplifier class: Push-pull Class A, no feedback
Sensitivity: 0.6V RMS [full output]
Output impedance: (measured @ 0.5A, 60 Hz) 2 ohms
Input impedance: 50k
Power Supply Input: Auto-switching 100V / 120V / 220 / 240V operation or linear supply user-switchable between 110/120 and 220/240 (contact us if in need of a 100V linear supply)
Power Supply Output: 12VDC 2.5 amps
Hum and noise: minimum 60mV RMS or 90dB below full output (20Hz-20kHz)
Power consumption from ac power source: 33W
Power output: with 4-ohm load: 1W, 1% THD, with 14-ohm load: 0.5W, 1% THD
Channel separation: (4-ohm loads) 46dB, 100Hz-10kHz, (14-ohm loads): 54 dB, 100Hz-10kHz
Frequency response full power: (4-ohm load) +0, -1dB 10Hz-20kHz, (14-ohm load): +0, -1dB 5Hz-50kHz,
Voltage gain: (4-ohm load): 10.3dB, (14-ohm load): 12.4dB
Size:
Amplifier: 9 1/2 inches (24.1 cm) wide, 4 3/4 inches (12.0 cm) tall, 7 7/8 inches (19.7 cm) deep (including connectors)
Linear power supply: 12" (30.48 cm) x 3.25" (8.26 cm) x 4.25" (10.8 cm)
Net weight:
With switching supply: 5.35 lbs (2.5 kg) - amplifier and external power supply)
With linear supply: 8.94 lbs (4.1 kg) - amplifier and external power supply)
Finish: Aluminum case w/ lexan top
Tube complement: 2 x 12AT7 input, 2 x 6SN7 or 12SN7 output. (We supply NOS 12SN7 tubes by default. Jumpers on the circuit board allow you to easily switch between 12V and 6V, allowing you to use both 6SN7 and 12SN7 tubes and expanding your tube choices. The 12SN7 and 6SN7 are sonically identical and differ only in their heater voltage.) 12AU7 tubes can replace the 12AT7 tubes to lower the gain.
[url=https://servimg.com/view/20314502/54]
